Jenfab LeanClean 360-4

Unit is in very good condition.

S/N 12438

Date of Mfg 2015

Notes:
1. Primary Electrical Power Supply 460v/3ph/60hz
2. Water piping to tanks copper with solenoid valves controlled by float switch level controls for automatic level control..
3. Spray piping all stainless steel with bag filter/Chip Baskets on each the wash and rinse lines.
4. Temperature controlled by the PLC with temperature probes in each tank and dryer.
5. Ultra Sonics (no)
6. DI Fresh Water Rinse (yes)
7. Oil coalescer (yes)
8. Auto Pump Out Drain Station
9. External PLC Programming Port

The Lean Clean 360 is a fast, high-performance parts washer that removes oils, chips, and other contaminates from new or used parts.

The Jenfab LeanClean 360-4 model cleans four baskets side by side at the same time. This provides better cleaning, rinsing, and drying as well as faster, more efficient loading than baskets that are stacked on top of each other, two by tow. The standard machine includes two process tanks for wash and rinse with an option to add a third tank.

Operators place 4 basket of parts into the Lean Clean and press the start button. The Lean Clean 360 submerges and rotates the baskets while directing 180 gallons per minute of cleaning solution at the parts at 40 psig. The machine continually recirculates, filters, and delivers the cleaning solution to the basket of parts through high pressure submerged jets.

The Lean Clean turns over the entire volume of the cleaning chamber more than twice a minute, flushing away chips, soils and oils, and keeping fresh, clean solution in contact with the parts.

After washing, the cleaning machine drains the washing solution
and completes an equally vigorous rinse cycle with water (or water with inhibitors).

After rinsing and draining, a high volume, high velocity recirculating convection dryer dries the parts by delivering air through multiple slots aimed directly at the rotating basket of parts.

Typical Wash Cycle

A typical wash cycle includes the following steps:

Loading—operator slides baskets into the machine, closes the door, and presses the Cycle Start button.

Washing—wash pump rapidly fills the process chamber and volume turbulation begins.

Draining—baskets rotates and drains solution from parts as the process chamber empties into holding tank.

Rinsing—rinse spray begins to impinge as the process tank fills for a combined soak-and-spray rinse.

Fresh Water Rinse—fresh water spray begins to impinge for final rinse as parts rotate.

Drain—parts rotate to drain solution and dryer starts.

Dry—6000 cfm recirculating hot air convection dryer directs heated air at high velocity through multiple high volume slots.

Unload—operator opens door and slides baskets out
of system.

Optional Features Included

The following sections describe optional equipment available for the Lean Clean 360-1. Check your Lean Clean 360 or your purchasing specifications to determine which options your machine includes.

Oil Separator (Coalescing Type)
The coalescing oil separator extends bath life by continually removing oils from the wash solution. The oil separator consists of a free-standing unit with an air-drive pump to pump solution from the
wash tank. Clean solution flows by gravity back to the wash tank.
Oleophilic (oil attracting) coalescing tubes capture, agglomerate, and float oil globules to the surface where an adjustable weir discharges the oil from the separator. The tubes consistently remove oil globules 20 microns and larger at a capacity of 10 mg/l. The coalescer removes only oil, not chemistry.

External PLC Programming Port or Modem
The external PLC programming port enables programming from
an external computer. By adding the optional modem, JENFAB engineers can make programming changes or diagnose problem remotely, lowering service and troubleshooting costs.

Summary of Specifications

Lean Clean 360-4
Item Specification

Floor space:
122-3/4” W x 92-3/4”’ D x 111” H
Dry Weight 5,300 lbs.

Load Height: 42”

Process Chamber:
Size 125 Gal.

Wash Tank :
375 Gallons,Heat to 160 Deg; F.40 KW
Stainless Steel Pump 180 GPM@80 PSI 10 HP
Bag Filter #2 Size Stainless Steel
Chip basket on rinse tank

Rinse Tank
375 Gallons,Heat to 160 Deg; F. 40 KW
Stainless Steel Pump 180 GPM@80PSI 10 HP
Bag Filter #2 Size Stainless Steel
Chip basket 12” x 12”
Mini oil coalescer

Dryer Blower:
6000 CFM@4” S.P.~7 ½ HP Recirculating
Heat to 180 Deg. F. ~ 40KW
80 DB Max Sound Level

Pump Out Station:
Automatic Pump Out Station with
Diaphragm pump and level switches for
Auto pump out. Pumping rate is Approx.
25 GPM @ 30 PSI

Controls:
Allen Bradley Micrologix 1400 PLC
Memory For additional programs
External PLC Port
Modem

Basket Size:
12x20x8” or 24x20x8”
Originally Sold with (8) of the smaller baskets and (2) of the larger baskets.

Cycle Time:
10 Minutes (Wash, Rinse, Dry)
Four Baskets Per Cycle
Rotation Speed~adjustable up to 6 RPM
BASED on 6 Cycles Per Hour: 24 JENFAB Baskets produce 24 Cubic feet/hr

Stainless Steel Tanks, Cleaning Chamber, Pumps

Polished Stainless Steel Housing

Chip Collection Baskets (Easy Lift Out)

Fork Lift Pockets

FOB, Miami, OK